自由锻件公司
产品简介
详细信息
材料对自由锻件锻压设备的适应性
自由锻件铝合金:锻造变形量很大时,优先选用水压机,否则可任选。
铍合金:优先选用水压机,因慢速下的可锻性良好。
铜合金:优先选用锤、螺旋压力机或曲柄压力机,但对变形速率敏感的青铜和高锌黄铜,应优先选用水压机。
铌合金:锤、螺旋压力机和曲柄压力机,当合金请求高温锻造时,优先选用水压机。
镁合金:因其快速变形的可锻性差,应优先选用水压机。
钼合金:当请求高温锻造时,优先选用锤、螺旋压力机或曲柄压力机。
镍基合金:根据锻件的截面厚度选定;锻造薄的截面(小于12. 7毫米)锻件时,优先选用锤、螺旋压力机、曲柄压力机,否则可任选。
碳钢和低合金钢:锻造含有薄的截面的锻件或氧化皮肃清较难题时,优先选用锤、 螺旋压力机或曲柄压力机,否则可任选。
不锈钢:含有薄截面的锻件,优先选用锤、螺旋压力机或曲柄压力机,否则可任选。
钽合金:高温锻造时,优先选用锤、螺旋压力机或曲柄压力机。
钛合金:含有薄截面的锻件,优先选用锤、螺旋压力机或曲柄压力机,否则可任选。
钨合金:高温锻造时,优先选用锤、螺旋压力机或曲柄压力机。
锆合金:当毛坯有包套时,优先选用水压机(高于760℃);锻造温度低于 760℃的,可任选。
自由锻件公司哪家好,就找唐山盛通锻造有限公司。
Adaptability of materials to free forging press equipment
Free forging aluminum alloy: When the forging deformation is large, the hydraulic press is preferred, otherwise it can be optional.
Niobium alloy: The hydraulic press is preferred because of the good forgeability at slow speed.
Copper alloy: Hammer, screw press or crank press are preferred, but bronze and high-zinc brass, which are sensitive to deformation rate, should be preferred.
Niobium alloys: hammers, screw presses and crank presses. When alloys are required for high temperature forging, hydraulic presses are preferred.
Magnesium alloy: Due to its poorly deformable forgeability, a hydraulic press should be preferred.
Molybdenum alloy: When high temperature forging is requested, hammer, screw press or crank press are preferred.
Nickel-based alloy: selected according to the section thickness of the forging; forging a thin section (less than 12.7 mm) forging, it is preferred to use a hammer, a screw press, or a crank press, otherwise it may be optional.
Carbon steel and low-alloy steel: When forging a forging or a scale with a thin section, it is preferable to use a hammer, a screw press or a crank press, otherwise it may be optional.
Stainless steel: Forgings with a thin section, preferably a hammer, screw press or crank press, otherwise optional.
Niobium alloy: For high temperature forging, hammer, screw press or crank press are preferred.
Titanium alloy: Forgings with a thin section, preferably a hammer, screw press or crank press, otherwise optional.
Tungsten alloy: For high temperature forging, hammer, screw press or crank press are preferred.
Zirconium alloy: When the blank has a wrap, the hydraulic press (above 760 ° C) is preferred; the forging temperature is lower than 760 ° C, optional.