百分零部件网

• 01 CRC质量管理体系认证

  风机测试符合JB/T 10563-2006国家标准的要求，风机设备连续运行24小时不损坏，长久使用寿命，节能高效（省电），为您创造利润，节省成本。全机组进行电脑应力应变分析，提高结构强度。

• 02 保养操作简单

  采用油浴封闭式的机油箱，保护轴承与轴芯不受腐蚀性气体的侵蚀，延长使用寿命，降低故障频率，模组化生产，规格统一，零配件材料齐全，可在短时间内、节约成本，快速完成安装维修。

• 03 提供服务团队

  1对1服务，提供到公司测量性能、震动，提供测试报告，防范故障于未然，保障风机在状况下运转。可针对客户的特殊规格，量身定制设计，确保风机运转于率点。

• 不锈钢4-72C型离心通风机

  不锈钢4-72C型离心式通风机可输送空气和其它不自燃的、对人体无害的、对钢材无腐蚀性的气体。气体内不允许有粘性物质，所含尘土及硬质颗粒物不大于150mg/m3。气体温度不得超过80℃该风机广泛适用于工矿企业、大型建筑物、宾馆酒楼等室内通风换气排烟。
  产品型式:本公司号有NO2.8、3.2、3.6、4、4.5、5、5.6、6、6.3、7.1、8、10、12十三种。可制成右旋和左旋两种型式，叶轮顺时针旋转，称为右旋风机。以“右”表示，叶轮逆时针旋转，称为左旋风机，以“左”表示。风机的出口位置，以机壳的出风角度表示。4-72NO2.8-10出厂时均做成多种型式，可根据使用单位要求安装成所需的位置，即出风口位置调整范围0°~225°间隔是22.5°或45°，即（0°、45°、90°、135°、180°、225°）共六种。NO7.1-10根据用户需求制成一种方向角度。风机的传动方式为C式。
  结构特点:本风机主要由叶轮、机壳、进风口、机架、轴承箱等皮带传动而组成。叶轮：由10个后倾斜的机翼型叶片、曲线型前盘和平板后盘组成。并经过动平衡校正，气动性能，故运转平衡、振动小、效率高、寿命长等特点。机壳：用钢板焊成蜗型壳体。进风口：制成整体（全部模具成型），装于风机的侧面，于轴向平行的戴面未曲线形状，能使气体顺利进入叶轮，且损失较小。传动组：由主轴、轴承箱、联轴器等。主轴由优质钢制成，轴承箱整体结构，采用滚动轴承，分为水冷和油冷两种。

• Stainless steel 4-72C centrifugal fan

  Stainless steel 4-72C centrifugal fan can transport air and other non-self-igniting, harmless to the human body, non-corrosive to steel. No viscous substances are allowed in the gas, and the dust and hard particles contained in the gas are not more than 150 mg/m3. The gas temperature should not exceed 80 °C. The fan is widely used in industrial ventilation enterprises, large buildings, hotel restaurants and other indoor ventilation and smoke exhaust. Product type: The company has NO2.8, 3.2, 3.6, 4, 4.5, 5, 5.6, 6, 6.3, 7.1, 8, 10, 12 and thirteen. It can be made into two types: right-handed and left-handed. The impeller rotates clockwise and is called a right-handed fan. Expressed as "right", the impeller rotates counterclockwise, called the left-handed fan, and is represented by "left". The exit position of the fan is expressed by the air outlet angle of the casing. 4-72NO2.8-10 is made into various types at the factory, and can be installed to the required position according to the requirements of the unit of use. That is, the position of the air outlet is adjusted from 0° to 225°, and the interval is 22.5° or 45°, that is (0 There are six kinds of °, 45°, 90°, 135°, 180°, and 225°. NO7.1-10 is made into a direction angle according to user requirements. The fan is driven in the C mode. Structural features: The fan is mainly composed of impeller, casing, air inlet, frame, bearing box and other belt transmission. Impeller: consists of 10 rear-tilted airfoil blades, curved front discs and flat rear discs. After dynamic balance correction and aerodynamic performance, it has the characteristics of balanced operation, small vibration, high efficiency and long service life. Housing: welded with a steel plate into a volute casing. Air inlet: made into a whole (all mold molding), installed on the side of the fan, the axially parallel wear surface has no curved shape, which enables the gas to smoothly enter the impeller with less loss. Transmission group: from the main shaft, bearing housing, coupling and so on. The main shaft is made of high-quality steel. The overall structure of the bearing housing is made of rolling bearings and is divided into water-cooling and oil-cooling.

外形及安装尺寸示意图 Lnstallation size diagram

产品为人工实物测量会有一定误差，相关数据仅作参考，以收到的实物为准。 单位Unit: mm(毫米）