电动车车载充电器/DC-DC转换器自动测试系统 Model 8000
产品简介
详细信息
此系统针对电动/混合动力汽车的车载充电器与DC/DC转换器的输入/输出特性、效率与保护项目测试。
优化后的标准测试项目(On-Board Charger):
可符合QC/T 895-2011法规标准
Charger Pre-setup (初始设定)
- Charger Input/Output Test (输入输出测试)
- Charger Line Regulation Test(输入效应测试)
- Charger Load Regulation Test(负载效应测试)
- Charger Hold On Adjust Test(在线调整测试)
- Charger Fin Ramp Shut Down Test(输入频率极限测试)
- Charger Fin Ramp Start Up Test(开机频率极限测试)
- DSO Setup For 4 Channels(数位式示波器设定/4 Channels)
- Charger Cursor Measure Time(光标量测时间)
- Charger Load Setup(负载设定)
- Charger Over Load Protection Test(过载保护测试)
- Charger OVP (CC Mode) Test(负载定电流模式下过电压测试)
- Charger OVP (CV Mode) Test(负载定电压模式下过电压测试)
- Charger Peak Current Test(峰值电流测试)
- Charger Ripple & Noise Test(涟波及杂讯测试)
- Charger Short Circuit Protection Test(输出短路保护测试)
- Charger Static Test(静态测试)
- Charger Vin Ramp Shut Down Test(输入电压极限测试)
- Charger Vin Start Up Test(开机输入电压极限测试)
- Charger Waveform Measure Test(波形量测)
- Charger Waveform Measure Turn On Test(开机波形量测)
- Charger Waveform Measure Turn Off Test(关机波形量测)
- Enable Turn On/Off Charger
- CAN Bus Reading Charger
优化后的标准测试项目(DC-DC Converter):
可符合GB/T 24347-2009法规测试
DD-System Pre-setup(系统初始设定)
- DC-DC Input/Output Test(输入输出及效率测试)
- DC-DC Line Regulation Test(输入效应测试)
- DC-DC Load Regulation Test(负载效应测试)
- DC-DC Hold On Adjust Test(在线调整测试)
- DSO Setup For 4 Channels(数位式示波器设定/4 Channels)
- DC-DC Cursor Measure Time(光标量测时间)
- DC-DC Over Load Protection Test(过载保护测试)
- DC-DC Over Voltage Protection Test(过电压保护测试)
- DC-DC Peak Current Test(峰值电流测试)
- DC-DC Ripple & Noise Test(涟波及杂讯测试)
- DC-DC Short Circuit Protection Test(短路保护测试)
- DC-DC Total Regulation Test(总效应测试)
- DC-DC Vin Ramp Shut Down Test(输入电压极限测试)
- DC-DC Vin Ramp Start Up Test(开机输入电压极限测试)
- DC-DC Waveform Measure Test波形量测)
- DC-DC Waveform Measure Turn On Test(开机波形量测)
- DC-DC Waveform Measure Turn Off Test(关机波形量测)
- Total Efficiency Test(总效率量测)
- Enable Turn On/Off DC-DC
- CAN Bus Reading Charger
CAN Bus Pre-Setup(初始讯息设定)